Home »
Techniek » Resistentie Lijst -Chemische stoffen
Techniek - Resistentie Lijst -Chemische stoffen
Turbo Liner Products Chemical Resistance Information and Testing
| Table 1
| Chemical Resistance ASTM D 1308
| Chemical
| Aromatic Polyurea
| Aliphatic Polyurea
| Acetone
| A
| A
| Brake Fluid
| B
| C
| CLOROX®, 10%
| NR1
| A
| Dimethyl Formamide
| NR
| NR
| Gasoline, unleaded
| A
| A
| Hexane
| A
| A
| Hot tub water
| B
| A
| Hydraulic oil
| A
| C
| JEFFAMINE® D-400
| NR
| NR
| Methanol
| A
| C
| 5% Methanol/gasoline
| A
| C
| Motor Oil
| B1
| B1
| Propylene carbonate
| C
| C
| Sodium hydroxide, 5%
| A
| A
| Sodium hydroxide, 10%
| A
| A
| Sodium hydroxide, 25%
| A
| A
| Sodium hydroxide, 50%
| B1
| B1
| Sulfuric acid, 5%
| A
| B
| Sulfuric acid, 10%
| B
| B
| Sulfuric acid, 50%
| NR
| NR
| Sulfuric acid, concentrate
| NR3
| NR3
| Vinegar, 5% acetic acid
| A
| B
| Water
| A
| A
| Sodium Hypochlorite, 10%
| A1
|
| Sodium BiSulfite, 40%
| A
|
|
|
|
|
|
|
|
| Code describing chemical's effect on elastomer
|
| A - No visible damage
| 1 - Some discoloration only
| B - Little Visible damage
| 2 - Brominated water
| C - Some effect/swelling, discoloration, cracking
| 3 - Less than 24 hour exposure
|
|
| NR - Not recommended
|
|
|
|
ASTM D 3912: Chemical Resistance of Coating Used in Light-Water Nuclear Power Plants
This test method describes the immersion method of exposure for a coating system to chemicals. In this testing procedure, a black pigmented aromatic polyurea spray elastomer system was used. This system was spray applied to 2 mil blast profile steel panels, giving total encapsulation. These coated panels were then immersed half way into individual chemicals for a period of 1 year at 25o C, except where noted. The panels then removed and inspected. Chemicals used as well as results can be found in Table 2.
|
|
|
| Table 2
| Chemical Resistance ASTM D 3912
| Chemical
| 12 Month Exposure
| Methanol
| S., swelling < 48hrs
| Gasoline
| Slight surface change, no hardness loss
| Diesel fuel
| No visible damage
| Toluene
| S. swelling, < 24hrs
| MTBE
| Slight surface change
| 5% MTBE/Gasoline
| Slight surface change
| Motor Oil
| Slight surface change, no hardness loss
| Hydraulic Fluid
| Slight surface change, no hardness loss
| 2-Methylbutane
| No visible damage
| Water - room temperature
| No visible damage
| Water - 82oC, 14days
| No visible damage
|
|
| 10%NaCl/Water
|
| Room Temperature
| No visible damage
| 50oC, 14 days
| No visible damage
|
|
| 10% Sugar/Water
| No visible damage
|
|
| Sulfuric Acid - 5%
| No visible damage
| Sulfuric Acid - 10%
| No visible damage
| Sulfuric Acid - 3%, 50oC, 14days
| No visible damage
| Hydrochloric Acid - 5%
| No visible damage
| Hydrochloric Acid - 10%
| No visible damage
| Phosphoric Acid - 10%
| No visible damage
| Ammonium Hydroxide - 10%
| No visible damage
| Ammonium Hydroxide - 20%
| No visible damage
| Sodium Hydroxide - 10%
| No visible damage
| Sodium Hydroxide - 20%
| No visible damage
| Sodium Hydroxide - 50%
| Slight surface discolor, no hardness loss
| Sodium Hydroxide - 1%, 50oC, 14 days
| Slight surface discolor, no hardness loss
| Potassium Hydroxide - 10%
| No visible damage
| Potassium Hydroxide - 20%
| Slight surface discolor, no hardness loss
| Acetic Acid - 10%
| No visible damage
|
|
|
|
DISCLAIMER All guidelines, recommendations, statements, and technical data contained herein are based on information and tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. It is the users responsibility to satisfy himself, by his own information and test, to determine suitability of the product for his own intended use, application and job situation and user assumes all risk and liability resulting from his use of the product. We do not suggest or guarantee that any hazard listed herein are the only ones which may exist. Neither seller nor manufacturer shall be liable to the buyer or any third person for any injury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether in writing or oral, other than those contained herein shall not be binding upon the manufacturer, unless in writing and signed by a corporate officer of the manufacturer. Technical and application information is provided for the purpose of establishing a general profile of the material and proper application procedures. Test performance results were obtained in a controlled environment and Turbo Products makes no claim that these tests or any other tests, accurately represent all environments. For information contact: Turbo Liner Inc. 1 West Cameron Kellogg, ID 83837 1-877-678-8726